Cables and adapters to buy, prices, reviews. Cables and adapters in online store Pro ECU, characteristics, description, photos.

Universal cable DB15-PIN allows connecting to different connectors of electronic control units. Is an improved analogue 14P600KT02. Created and produced by us to work with the entire line of 'PowerBox', but also suitable for K-TAG and KESS2. When working with a 'PowerBox for PCMflash' replaces two cable 14P600KT02 and 14P600KT06. Not to mix the same color, GPT1 and GPT2 are additionally marked and displayed in a sep..

$28.94

In stock

CombiBox switching device for PCMflash

CombiBox is designed for connecting the control unit to the PCMflash loader and the j2534 adapter "on the table" and switching power supply voltages and generating BOOT, CNF1 signals. When used with the Scanmatik 2 (PRO) adapter, the device allows you to generate gpt1 and GPT2 signals necessary for working with modules 53 and 71, as well as with advanced modules. Power supply: For CombiBox to w..

$86.81

In stock

The switching device CombiBox Combiloader

CombiBox is designed to connect the control unit to the Loader Combiloader and adapter DIALink 'on the table' and switching the supply voltage signals to GPT1, GPT2, and signal conditioning BOOT, CNF1. Power supply. To work CombiBox must submit the stabilized voltage supply of 12V. Mating connector included in the package. You must pay attention to the correct polarity when wiring power cable. ..

$81.02

In stock

The switching device PowerBox for CombiLoader

This device is designed to connect the control unit to the loader software 'on the table' and switching supply voltages and GPT1, GPT2, and the formation of signals of BOOT, CNF1. Working in automatic mode with the loader CombiLoader, and in manual mode, any bootloader which is 'the logic manual'. Complete only the device without cables. Cables, see tab, 'Companion'. Controls: The device is..

$75.24

In stock

The switching device PowerBox for PCMflash

Switching device for PCMflash PowerBox is designed to connect the control unit to the loader software 'on the table' and automatic (if supported by the bootloader and the J2534 adapter) or manual switching of supply voltages and the generation of signals RESET, BOOT, CNF1, GPT1, GPT2, WATCHDOG. Working in automatic mode with the boot loaders that are used to control: BOOT - OEM12, 12 contact OB..

$115.75

In stock

Adapter BITS001

A special adapter to connect the control units on the table. Performs automatic power management, and boot pins through the J2534 adapter.* Required to read in the BSL mode for control units Bosch M7.8/ME7.8.8 and Continental SIM2K-25x/26x * - tested and guaranteed works with Tactrix OpenPort 2.0 ..

$46.30

In stock

Adapter DENSO - UART - MBUS 3 1

Universal adapter to work: panel DENSO UART at MBUS The Board has the following pin: DTR DTS TX RX IGN GND 12V 3.3 V 5V MBUS Designed to work with the modules of the software complex MDFLASHER ..

$104.17

In stock

Adapter DENSO - UART - MBUS 3 1

Universal adapter to work: panel DENSO UART at MBUS The Board has the following pin: DTR DTS TX RX IGN GND 12V 3.3 V 5V MBUS Designed to work with the modules of the software complex MDFLASHER ..

$57.87

In stock

Adapters for programming 22 PCs (heads)

Complete set of adapters for KESS/K-TAG/Dimsport BDM Denso, Marelli, Bosch, Siemens With this kit You can successfully connect to the blocks of the ECU via contact pad (nickels) on the Board. On the adapters, there is indication of power to the ECU. Set includes: 144300KBDM - BDM Motorola MPC5xx Kit contains adapters: 14AM00T00M 14AM00T01M 14AM00TBAS 14AM00TB01 14AM00TB..

$75.40

In a remote warehouse

Boot/Bench cable for Scanmatik 2

The cable is available in two versions: 1. Universal adapter for SM2/SM2PRO + PCMflash scanner with automatic control of power supply to the unit. Indication: Red - power adapter Green - power on of the POWER+12v unit Purpose of the cable wires: POWER+12V - red GND - black CAN-H - white CAN-L - green K-Line - Yellow GPT1 - yellow/red ..

$46.30

In stock

Cable DB9 9pin - 16pin OBD2

DB9 - OBD2 cord can be used to connect to diagnostic connector OBD2 car. Cord DB9 connector has the following Pinout: 1,2 - the mass 3 - CAN High 4 - ISO 9141-2 K Line 5 - CAN Low 6 - J2850 BUS- 7 - J2850 BUS+ 8 - ISO 9141-2 L Line 9 - Uninterruptible power ..

$16.59

In stock

Cable M74.8 Cable for Combiloader

Cable for recording the M74.8 ECU using the Combiloader and the corresponding module. ..

$34.72

In stock

Cable OBD2 Male - OBD2 Female x 2 (double)

Cable OBD2 Male - OBD2 Female x 2 (double) ..

$25.64

In stock

Extension cable OBD2 1.5 meters

Universal OBD2 extension cable is a five-foot cable with soldered on ends 16-pin connectors. On the one hand, 'daddy' (for connection to diagnostic socket of car) and 'mom' (to connect to a scanner or KKL adapter). A distinctive feature of this extension is that the connectors are soldered all sixteen pins, not just the K-Line (7th), plus a 12V (16th) and mass (4th and 5th), as it happens in the case of goods of poor qualit..

$31.67

In stock

Socket DIP8-SOIC8 ZIF

Designed for easy programming of chips in SOIC8 housing ..

$3.47

In stock

UPA adapters for programming TMS + NEC

Set of two adapters TMS + NEC programmer UPA ..

$66.35

In stock

The cable Converter USB-COM for emulators B2C and OZONE

The Converter cable is designed for communication devices and OZONE, OZONE-MONO, B12S12 and B2C work with M. C. E. B2Catalyst Devices configurator and configurator respectively, installed on your computer, or laptop with built-in USB port. ..

$13.89

In stock

OBD2 Female diagnostic connector

External view connector (male) and DLC (female). Pin assignments connector diagnostics standard OBD-II is given in the table. Unused contact pads for the car manufacturers use for their purposes. To determine which diagnostic Protocol is used on a specific car, with sufficient share of probability it is possible accordin..

$10.56

In stock

OBD2 Male diagnostic connector (plug)

The appearance of the connector and the DLC. Pin assignments connector diagnostics standard OBD-II is given in the table. Unused contact pads for the car manufacturers use for their purposes. To determine which diagnostic Protocol is used on a specific car, with sufficient share of probability it is possible according to..

$9.05

In stock

Main cable Scanmatik-2

To connect any of the adapters from the kit Scanmatik 2. ..

$20.83

Expected arrival

Adapter for CF Moto technology OBD2 - 3pin

Openport allows you to connect directly to the diagnostic connector of the Quad and read the entry without removing the control unit. ..

$23.15

Expected arrival

Cable universal 14Р600КТ02 (analog)

The cable can be used in conjunction with a GPT adapter for PCMflash to connect your ECU 'on the table'. ..

$19.68

Expected arrival

Connectors for ECU Toyota/Lexus

20 pin connectors for soldering in the ECU, Toyota/Lexus and subsequent programming via the Bootloader firmware Toyota Lexus ECU Flasher. ..

$0.17

Expected arrival

GPT adapter

The adapter is used by 53 PCMflash module to read passwords. Features of the adapter: The connection blocks according to the Reference to K-Tag. Connector DB-15 Pinout divorced under the cable K-Tag 14Р600КТ02 Power management BU: automatic, off or manual mode Booth pins (boot, reset, CNF1, VPP) connect software Signals to GPT1, GPT2 displayed on individual contacts and duplicated on the ..

$34.72

Delivery suspended

GPT adapter ChipSoft

CHIPSOFT GPT Adapter is designed to generate the necessary signals to read password Tricore CPU (ECU of modern cars BMW, Mercedes, etc). The adapter is made in the form of a circuit Board that connects to OBD2 BreakOut Box CHIPSOFT. Additionally, the adapter provides 4 boot pins to 3.3 V via a resistor of 1K (used to work with the ECU Tricore ). ChipLoader module Tricore, CHIPSOFT J2534, OBD2 BreakOut Box..

$19.77

Expected arrival

GPT adapter for reading passwords

Adapter GPT is intended for use with a J2534 adapter and allows you to read passwords in BSL mode, to ECU processor-based TriCore technology GPT. ..

$45.24

Expected arrival

GPT adapter PCMflash for owners of Tricore Module BSL

The adapter is used by 53 PCMflash module to read passwords. ..

$5.79

Out of production

Head for ECU Toyota/Lexus

Head for the Bootloader firmware Toyota Lexus ECU Flasher. Allows ECU programming without pre-soldering the connector to the Board. Designed to work with the table positioner. ..

$34.72

Delivery suspended

Socket to unlock Bosch ME17.9.71 without soldering

Opens the loading of the Bosch ME17.9.71 unit with one touch into the verified 4 platforms (fifth, not connected to the chain - centering) control unit with the help of springy needle contacts PogoPin. If you wish, you can turn on the backlight of the connection location (crocodile connectors). ..

$16.20

Expected arrival

Splitter signals OBD2 Breakout Box v2

Splitter signals OBD2 Breakout Box v2 is designed to work with ECU on the table with J2534, KLine or any other adapter, without reference to the loader or the program. Board implemented: Reverse polarity protection Fuse DIP switch for setting 60/120 Om on CAN bus Comb 4 to 15 2 DB9 connectors (mom and dad) Automatic power management using L-Line 2 bottles of Pina (6.8 K and 1K..

$46.91

Expected arrival

DB25 Мale in the case

Connector DB-25 is Used for self-Assembly of cables Combiloader SMS, SMS 2 and other Diagnostic. ..

$4.52

Expected arrival

Cables and adapter

Refine Search

add to cart

Information

Customer Service

Extras

My Account

Our contacts