Module for editing firmware of Denso control units of gasoline turbocharged Toyota Yaris GR 1.6 Turbo cars with G16E-GTS engine.
Files from MCU1 8A 230-52 XXX and MCU 0 8A 220-52 XXX are available for editing
Only 4MB files are supported.
The following MCU1 8 A 230-52 XXX cards are available:
Air control: Efficiency in additional mode, Maximal mass air flow
Boost control: limitation: Boost correction factor, Maximal boost pressure absolute, Torque clamp boost limiter, Boost limitation absolute, Boost limitation by torque, Boost limitation relative, Maximal boost relative
Boost control: wastegate: Target wastegate duty, Wastegate duty in additional speed
Camshaft Control: Intake Camshaft, Intake camshaft correction, Intake camshaft correction factor
Engine speed limit: Engine speed limitation
Fuel Pressure: Target fuel pressure, Maximum fuel pressure
Fuelling Direct Injection: Injection I angle in additional mode, Injection II angle in additional mode
Ignition Optimum: Spark advance optimal
Sensors scaling: Mass air flow sensor scaling
Spark advance: Ignition efficiency, Minimal spark advance, Spark advance in additional mode, Spark advance main, Spark advance retardation on camshaft, Spark advance warmup correction
Throttle control: Primary throttle efficiency in additional gear, Primary throttle efficiency 1 [Normal mode], Primary throttle efficiency 1 [Sport mode], Primary throttle efficiency 2 [Normal mode], Primary throttle efficiency 2 [Sport mode], Primary throttle efficiency base, Primary throttle efficiency [gear 2], Throttle efficiency idle, Throttle position base
Throttle: direct control: Throttle control limit in additional gear [Normal], Throttle control limit in additional gear [Sport], Throttle direct control limit [1st GEAR], Throttle direct control limit [1st GEAR] AWD High, Throttle direct control limit [1st GEAR] AWD Low, Throttle direct control limit [Reverse GEAR], Throttle direct control limit
Torque model: Calculated torque from load, Engine speed by throttle position, Maximal engine torque, Torque Limiter, Torque limiter by temperature, Maximal torque
Vehicle speed limit: Vehicle speed limiter (if found)
The following MCU cards are available 0 8A220-52 XXX:Air Control:
Air mass flow sensor slope, Maximum MAP sensor
Deactivation: Deaclivation turbo charger protection
Engine Torque: Limiter of maximum torque, Torque request during take off condition in additional mode, Maximum Boost Limiter of Turbo Pressure
Injection Warm Up: Injection warm up in additional mode
Rail Pressure: Rail Pressure in additional mode
Torque model: Limiter of Maximum torque, Optimal engine torque
Spark Advance: Minimum Spark Advance, Spark Advance, Spark Advance base , Spark Advance correction , Spark Correction Water temperature
List of supported software versions:
8A2305208400 8A2305213000 8A2305207300
8A2205210000 8A2205204200 8A2305208300
8A2305204300 8A2205207200 8A2305204400
8A2205213000 8A2305205200 8A2205205000
8A2305207200 8A2205214000 8A2205212000
8A2305214000 8A2305210200 8A2205216000
8A2205208200 8A2305207400 8A2305206000
Driver usb key
The Program BitEdit
For technical support:
Manual activation modules BitEdit:
Install the driver software for usb key and the program BitEdit.
Insert the key into a PC, run the program, Bitedit.
Let us know the serial number of your dongle (Dongle ID) indicating the number of your order info@ecupro.ru
After you receive activation notification, run the program, BitEdit on a PC with Internet connection.
We have fast worldwide delivery by EMS-post
We provide a guarantee for products and technical support
Our system of discounts and regular promotions save your money
